ESXi - 6.7 nvme

From Da Nerd Mage Wiki
Revision as of 17:39, 10 February 2022 by Tinker (talk | contribs) (→‎timeout)
Jump to navigation Jump to search

nvme

VMware NVMe driver esxcli extensions

device

  • list
List NVMe devices registered to VMware NVMe driver
  • esxcli nvme device list
  • get
Get NVMe device information
  • esxcli nvme device get OPTIONS
OPTIONS
 -A|--adapter=<str>    Adapter to operate on (required)

controller

  • list
List all controllers on the device if namespace is not specified, otherwise list all controllers the namespace attached
  • esxcli nvme device controller list OPTIONS
OPTIONS
 -A|--adapter=<str>    Adapter to operate on (required)
 -n|--namespace=<str>  Namespace ID attached. ID starts from 1

feature

  • cap
Get NVMe device feature supported capabilities information
  • esxcli nvme device feature cap ADAPTER
ADAPTER
 -A|--adapter=<str>    Adapter to operate on (required)

aec

  • get
Get NVMe device feature async event configuration information
  • esxcli nvme device feature aec get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature async event configuration information
  • esxcli nvme device feature aec set ADAPTER OPTIONS
OPTIONS
 -w|--fwnotices=<long> an asynchronous event notification is sent to the host for a Firmware
                       Activation Starting event, 0 for false, 1 for true, 0 will be passed as
                       default value, if not set
 -m|--nsnotices=<long> an asynchronous event notification is sent to the host for a Namespace
                       Attribute change, 0 for false, 1 for true, 0 will be passed as default
                       value, if not set
 -S|--save             save the attribute
 -v|--value=<long>     SMART health critical warnings bitmap to be set, refer to Figure 79, NVMe
                       1.2 SPEC (required)

apst

  • apst
Get NVMe device feature autonomous power state transition information
  • esxcli nvme device feature apst get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"

ar

  • get
Get NVMe device feature arbitration information
  • esxcli nvme device feature ar get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature arbitration information
  • esxcli nvme device feature ar set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Arbitration Burst value to be set (required)
 -x|--value2=<long>    Low Priority Weight value to be set (required)
 -y|--value3=<long>    Medium Priority Weight value to be set (required)
 -z|--value4=<long>    High Priority Weight value to be set (required)

er

  • get
Get NVMe device feature error recovery information
  • esxcli nvme device feature er get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • Set
Set NVMe device feature error recovery information
  • esxcli nvme device feature er Set ADAPTER OPTIONS
OPTIONS
 -e|--enable=<long>    deallocated or unwritten logical block error enable value to be set, 0 for
                       false (disable), 1 for true (enable), 0 will be passed as default value, if
                       not set
 -n|--namespace=<str>  Namespace to operate on, 0 will be passed as default value, if not set
 -S|--save             save the attribute
 -v|--value=<long>     Time limited error recovery value to be set (required)

hi

  • get
Get NVMe device feature host identifier information
  • esxcli nvme device feature hi get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"

hmb

  • get
Get NVMe device feature host memory buffer information
  • esxcli nvme device feature hmb get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"

ic

  • get
Get NVMe device feature interrupt coalescing information
  • esxcli nvme device feature ic get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature interrupt coalescing information
  • esxcli nvme device feature ic set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Aggregation threshold value to be set (required)
 -x|--value2=<long>    Aggregation time value to be set (required)

ivc

  • get
Get NVMe device feature interrupt vector configuration information
  • esxcli nvme device feature ivc get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature interrupt vector configuration information
  • esxcli nvme device feature ivc set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Interrupt vector value to be set (required)
 -x|--value2=<long>    Coalescing disable value to be set, 0 for false (enable), 1 for true
                       (disable) (required)

kat

  • get
Get NVMe device feature keep alive timer information
  • esxcli nvme device feature kat get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature keep alive timer information
  • esxcli nvme device feature kat set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -t|--timeout=<long>   timeout value for the keep alive feature to be set (required)

lba

* get
Get NVMe device feature LBA range type information
  • esxcli nvme device feature lba get ADAPTER OPTIONS
OPTIONS
 -n|--namespace=<str>  Namespace to operate on (required)
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"

nq

  • get
Get NVMe device feature number of queue information
  • esxcli nvme device feature nq get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"

pm

  • get
Get NVMe device feature power management information
  • esxcli nvme device feature pm get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature power management information
  • esxcli nvme device feature pm set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Power state value to be set (required)
 -w|--workload=<long>  Workload Hint to be set, 0 will be passed as default value, if not set

spm

  • get
Get NVMe device feature software progress marker information
  • esxcli nvme device feature spm get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set software progress marker feature information, will clear Pre-boot Software Load Count (PBSLC) to 0
  • esxcli nvme device feature spm set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute

tt

  • get
Get NVMe device feature temperature threshold information
  • esxcli nvme device feature tt get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature temperature threshold information
  • esxcli nvme device feature tt set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -s|--sensor=<long>    Threshold temperature select value to be set, 0 will be passed as default
                       value, if not set
 -u|--under            Set under temperature threshold
 -v|--value=<long>     Temperature threshold value to be set (required)

vwc

  • get
Get NVMe device feature volatile write cache information
  • esxcli nvme device feature vwc get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature volatile write cache information
  • esxcli nvme device feature vwc set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Volitale write cache enable value to be set, 0 for false (disable), 1 for
                       true (enable) (required)

wa

  • get
Get NVMe device feature write atomicity information
  • esxcli nvme device feature wa get ADAPTER OPTIONS
OPTIONS
 -S|--select=<str>     specify which value of the attributes to return, "current", "default",
                       "saved"
  • set
Set NVMe device feature write atomicity information
  • esxcli nvme device feature wa set ADAPTER OPTIONS
OPTIONS
 -S|--save             save the attribute
 -v|--value=<long>     Disable Normal value to be set, 0 for false (enable), 1 for true (disable)
                       (required)

firmware

  • activate
Commit downloaded firmware image to a specific slot
  • esxcli nvme device firmware activate ADAPTER OPTIONS
OPTIONS
 -a|--action=<long>    Activate action (required)
                          0: Downloaded image replaces the image indicated by the
                             firmware slot field. This image is not activated.
                          1: Downloaded image replaces the image indicated by the
                             firmware slot field. This image is activated at the next reset.
                          2: The image specified by the firmware slot field is
                             activated at the next reset.
                          3: The image specified by the firmware slot field is
                             requested to be activated immediately without reset.
 -s|--slot=<long>      Slot number. If the value specified is 0, then the controller shall choose
                       the firmware slot. (required)
  • download
Download firmware image to the device
  • esxcli nvme device firmware download ADAPTER OPTIONS
OPTIONS
 -f|--firmware=<str>   Firmware image path (required)

log

error

  • get
Get NVMe device error log information
  • esxcli nvme device log error get ADAPTER OPTIONS
OPTIONS
 -e|--elpe=<long>      Error log page entries. This value indicates the number of log entries you
                       wish to get. The maximum number of entries supported is device-specific.
                       (required)

fwslot

  • get
Get NVMe device firmware slot log information
  • esxcli nvme device log fwslot get ADAPTER

smart

  • get
Get NVMe device SMART log information
  • esxcli nvme device log smart get ADAPTER OPTIONS
OPTIONS
 -n|--namespace=<long> Namespace ID. If log page is supported on a per namespace basis this value
                       indicates the ID of namespace you wish to get log from. This parameter can
                       be omitted to request global log page.

namespace

  • list
List namespace on NVMe device
  • esxcli nvme device namespace list ADAPTER


  • get
Get nvme namespace information
  • esxcli nvme device namespace get ADAPTER OPTIONS
OPTIONS
 -n|--namespace=<str>  ID of namespace to get information from. ID starts from 1 (required)
  • create
Create namespace on NVMe device
  • esxcli nvme device namespace create ADAPTER OPTIONS
OPTIONS
 -c|--capacity=<long>  Namespace Capacity (required)
 -p|--dps=<long>       End-to-End Data Protection Type Settings (required)
 -f|--flbas=<long>     Formatted LBA Size (required)
 -m|--nmic=<long>      Namespace Multi-path IO and Namespace Sharing Capabilities (required)
 -s|--size=<long>      Namespace Size (required)
  • delete
Delete namespace on NVMe device
  • esxcli nvme device namespace delete ADAPTER OPTIONS
OPTIONS
 -n|--namespace=<str>  ID of namespace to delete, starts from 1 (required)
  • attach
Attach namespace on NVMe device
  • esxcli nvme device namespace attach ADAPTER OPTIONS
OPTIONS
 -c|--controller=<long>
                       Controller ID to attach. ID starts from 0 (required)
 -n|--namespace=<str>  Namespace ID to attach. ID starts from 1 (required)
  • detach
Detach namespace on NVMe device
  • esxcli nvme device namespace detach ADAPTER OPTIONS
OPTIONS
 -c|--controller=<long>
                       Controller ID to detach. ID starts from 0 (required)
 -n|--namespace=<str>  ID of namespace to detach. ID starts from 1 (required)
  • format
Change namespace format
  • esxcli nvme device namespace format ADAPTER OPTIONS
OPTIONS
 -f|--format=<long>    LBA Format(LBAF) (required)
 -m|--ms=<long>        Metadata Settings(MS). 0: Metadata is transferred as part of a separate
                       buffer. 1: Metadata is transferred as part of an extended data LBA.
                       (required)
 -n|--namespace=<long> Namespace ID (required)
 -p|--pi=<long>        Protection Information(PI). 0: Protection information is not enabled. 1:
                       Protection information is enabled, Type 1. 2: Protection information is
                       enabled, Type 2. 3: Protection information is enabled, Type 3. (required)
 -l|--pil=<long>       Protection Information Location(PIL). 0: PI is transferred as the last
                       eight bytes of metadata, if PI is enabled. 1: PI is transferred as the
                       first eight bytes of metadata, if PI is enabled. (required)
 -s|--ses=<long>       Secure Erase Settings(SES). 0: No secure erase operation requested. 1: User
                       Data Erase. 2: Cryptographic Erase. (required)

register

  • get
Dump NVMe device registers
  • esxcli nvme device register get ADAPTER

timeout

  • get
Get timeout value of IO timeout checker
  • esxcli nvme device timeout get ADAPTER
  • set
Set timeout value for IO timeout checker
  • esxcli nvme device timeout set ADAPTER OPTIONS
OPTIONS
 -t|--timeout=<long>   IO timeout seconds for internal checker. Maximum timeout value is 40. 0:
                       disable timeout checker. (required)

driver

loglevel

set           Set NVMe driver log level and debug level
Retrieved from ‘https://wiki.nerdmage.ca/index.php?title=ESXi_-_6.7_nvme&oldid=938’