ESXi - 6.7 network

network

Operations that pertain to the maintenance of networking on an ESX host. This includes a wide variety of commands to manipulate virtual networking components (vswitch, portgroup, etc) as well as local host IP, DNS and general host networking settings.

diag

• ping

Send ICMP echo requests to network hosts.

• esxcli network diag ping CMD_OPTIONS

CMD_OPTIONS
 -c|--count=<long>     Specify the number of packets to send.
 -D|--debug            VMKPing debug mode.
 -d|--df               Set DF bit on IPv4 packets.
 -H|--host=<str>       Specify the host to send packets to. This parameter is required when not
                       executing ping in debug mode (-D)
 -I|--interface=<str>  Specify the outgoing interface.
 -i|--interval=<str>   Set the interval for sending packets in seconds.
 --ipv4                Ping with ICMPv4 echo requests.
 --ipv6                Ping with ICMPv6 echo requests.
 --netstack=<str>      Specify the TCP/IP netstack which the interface resides on
 -N|--nexthop=<str>    Override the system's default route selection, in dotted quad notation.
                       (IPv4 only. Requires interface option)
 -s|--size=<long>      Set the payload size of the packets to send.
 -t|--ttl=<long>       Set IPv4 Time To Live or IPv6 Hop Limit
 -W|--wait=<str>       Set the timeout to wait if no responses are received in seconds.

ens

lcore

• list

List ENS contexts.

• esxcli network ens lcore list

• add

Create ENS context.

• esxcli network ens lcore add ID

ID
 -l|--lcore-id=<long>  ENS context id to be created. (required)

• remove

Destroy ENS context.

• esxcli network ens lcore remove ID

ID
 -l|--lcore-id=<long>  ENS context id to be destroyed. (required)

affinity

• get

Get the affinity for given ENS context.

• esxcli network ens lcore affinity get ID

ID
 -l|--lcore-id=<long>  ENS context id. (required)

• set

Set affinity for given ENS context.

• esxcli network ens lcore affinity set ID NODE

ID
 -l|--lcore-id=<long>  ENS context id. (required)
NODE
 -a|--affinity=<long>  Numa node affinity. (required)

switch

• get

Get the switch associated with given ENS context.

• esxcli network ens lcore switch get ID

ID
 -l|--lcore-id=<long>  ENS context id. (required)

• add

Associate given ENS context with given switch.

• esxcli network ens lcore switch add ID SWITCH

ID
 -l|--lcore-id=<long>  ENS context id. (required)
SWITCH
 -s|--switch=<str>     Switch name. (required)

• remove

Disassociate given ENS context from virtual switch.

• esxcli network ens lcore switch remove ID

ID
 -l|--lcore-id=<long>  ENS context id. (required)

maxLcores

• get

Get the maximum number of ENS contexts (lcores).

• esxcli network ens maxLcores get

• set

Set the maximum number of ENS contexts.

• esxcli network ens maxLcores set MAXCORES

MAXCORES
 -n|--maxlcores=<long> Number of maximum ENS contexts to be assigned. (required)

firewall

• get

Get the firewall status.

• esxcli network firewall get

set

Set firewall enabled status and default action.

• esxcli network firewall set PARAM

PARAM
    --enabled OR --default-action

• refresh

Load ruleset configuration for firewall.

• esxcli network firewall refresh

load

Load firewall module and rulesets configuration.

• esxcli network firewall load

unload

Allow unload firewall module.

• esxcli network firewall unload

ruleset

• list

List the rulesets in firewall.

• esxcli network firewall ruleset list

set

Set firewall ruleset status (allowedAll flag and enabled status).

• esxcli network firewall ruleset set LABEL CMD_OPTIONS

LABEL
 -r|--ruleset-id=<str>     The label of the ruleset. (required)
CMD_OPTIONS
 -a|--allowed-all=<bool>   Set to true to allowed all ip, set to false to use allowed ip list.
 -e|--enabled=<bool>       Set to true to enable ruleset, set to false to disable it.

allowedip

• list

list allowed ip addresses for rulesets.

• esxcli network firewall ruleset allowedip list

add

Add allowed ip address/range to the ruleset ruleset.

• esxcli network firewall ruleset allowedip add LABEL RANGE

• remove

Remove allowed ip address/range from the ruleset.

• esxcli network firewall ruleset allowedip remove LABEL RANGE

LABEL
 -r|--ruleset-id=<str> The label of the ruleset. (required)
RANGE
-i|--ip-address=<str> Allowed ip address/range for the ruleset. (required)

client

• get

Show the number of clients using a firewall ruleset.

• esxcli network firewall ruleset client get LABEL

add

Add a new client to a firewall ruleset. This enables the firewall ruleset and increments the number of clients using the ruleset.

• esxcli network firewall ruleset client add LABEL

remove

Remove a client from a firewall ruleset. This decrements the number of clients using the ruleset and if the number reaches zero the ruleset is disabled.

• esxcli network firewall ruleset client remove LABEL

LABEL
 -r|--ruleset-id=<str> The label of the ruleset. (required)

rule

• list

List the rules of each ruleset in firewall.

• esxcli network firewall ruleset rule list

ip

• get

Get global IP settings

• esxcli network ip get

• set

Update global IP settings

• esxcli network ip set

Configure the VMkernel Adapter Gateway by Using esxcli Commands

connection

• list

List active TCP/IP connections

• esxcli network ip connection list

dns

search

• list

List the search domains currently configured on the ESXi host in the order in which they will be used when searching.

• esxcli network ip dns search list

• add

Add a search domain to the list of domains to be searched when trying to resolve an host name on the ESXi host.

• esxcli network ip dns search add DOMAIN NETSTACK

• remove

Remove a search domain from the list of domains to be searched when trying to resolve an host name on the ESXi host.

• esxcli network ip dns search remove DOMAIN NETSTACK

server

• list

Print a list of the DNS server currently configured on the system in the order in which they will be used.

• esxcli network ip dns server list

• add

Add a new DNS server to the end of the list of DNS servers to use for this ESXi host.

• esxcli network ip dns server add DOMAIN SERVER

• remove

Remove a DNS server from the list of DNS servers to use for this ESXi host.

• esxcli network ip dns server remove PARAM

DOMAIN
 -d|--domain=<str>     The string name of a domain to remove from the list of search domains.
                       (required)
NETSTACK
 -N|--netstack=<str>   The network stack instance; if unspecified, use the default netstack
                       instance
SERVER
 -s|--server=<str>     The IP address (v4 or v6) of the DNS server to add to the DNS server list.
                       (required)
PARAM
--all, --server

interface

• list

This command will list the VMkernel network interfaces currently known to the system.

• esxcli network ip interface list

• set

This command sets the enabled status and MTU size of a given IP interface

• esxcli network ip interface set CMD_OPTIONS

CMD_OPTIONS
 -e|--enabled=<bool>   Set to true to enable the interface, set to false to disable it.
 -i|--interface-name=<str>
                       The name of the interface to apply the configurations. (required)
 -m|--mtu=<long>       The MTU size of the IP interface.

• add

Add a new VMkernel network interface.

• esxcli network ip interface add CMD_OPTIONS

CMD_OPTIONS
 -P|--dvport-id=<str>  DVPort ID of the connection point. This requires
                       --dvs-name to be given in the same command
 -s|--dvs-name=<str>   DVSwitch name of the connection point. This requires
                       --dvport-id to be given in the same command
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to create.
                       This name must be in the form vmkX, where X is a
                       number 0-255
 -M|--mac-address=<str>
                       Set the MAC address for the newly created VMkernel
                       network interface.
 -m|--mtu=<long>       Set the MTU setting for a given VMkernel network
                       interface on creation
 -N|--netstack=<str>   The network stack instance; if unspecified, use the
                       default netstack instance
 -p|--portgroup-name=<str>
                       The name of the vswitch port group to add this
                       VMkernel network interface to.

• remove

Remove a VMkernel network interface from the ESXi host. A VMKernel network interface can be uniquely specified by --interface-name or --portgroup-name or --dvs-name/--dvport-id. i.e. Providing its name or its connection point are two ways to uniquely specify a VMKernel network interface.

• esxcli network ip interface remove CMD_OPTIONS

CMD_OPTIONS
 -P|--dvport-id=<str>  DVPort ID of the connection point. This requires
                       --dvs-name to be given in the same command
 -s|--dvs-name=<str>   DVSwitch name of the connection point. This requires
                       --dvport-id to be given in the same command
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to remove.
                       This name must be in the form vmkX, where X is a
                       number 0-255
 -N|--netstack=<str>   The network stack instance; if unspecified, use the
                       default netstack instance
 -p|--portgroup-name=<str>
                       The name of the vswitch port group to delete this
                       VMkernel network interface from.

ipv4

• get

List the IPv4 addresses assigned to VMkernel network interfaces.

• esxcli network ip interface ipv4 get

• set

Configure IPv4 setting for a given VMkernel network interface.

• esxcli network ip interface ipv4 set CMD_OPTIONS

CMD_OPTIONS
 -g|--gateway=<str>    The default gateway for this interface. The value must be a valid IPv4
                       address. Gateway would be reset if not provided
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to set IPv4 settings for. This
                       name must be an interface listed in the interface list command. (required)
 -I|--ipv4=<str>       The static IPv4 address for this interface.
 -N|--netmask=<str>    The static IPv4 netmask for this interface.
 -P|--peer-dns=<bool>  A boolean value to indicate if the system should use the DNS settings
                       published via DHCPv4 for this interface.
 -t|--type=<str>       IPv4 Address type :
                           dhcp: Use DHCP to aquire IPv4 setting for this interface.
                           none: Remove IPv4 settings form this interface.
                           static: Set Static IPv4 information for this interface. Requires --ipv4
                       and --netmask options.

address

• list

List the IPv4 addresses assigned to VMkernel network interfaces.

• esxcli network ip interface ipv4 address list

ipv6

• get

Get IPv6 settings for VMkernel network interfaces. This does not include the IPv6 addresses which can be found in the "address list" command.

• esxcli network ip interface ipv6 get

• set

Configure IPv6 settings for a given VMkernel network interface.

• esxcli network ip interface ipv6 set CMD_OPTIONS

CMD_OPTIONS
 -d|--enable-dhcpv6=<bool>
                       Setting this value to true will enable DHCPv6 on this interface and attempt
                       to aquire an IPv6 address from the network
 -e|--enable-ipv6=<bool>
                       Setting this value to true enables IPv6 on thisinterface while setting it
                       to false disables IPv6 on this interface.
 -r|--enable-router-adv=<bool>
                       Setting this value to true will enable IPv6 Router Advertised IPv6
                       addresses to be added to this interface from any routers broadcasting on
                       the local network.
 -g|--gateway=<str>    A default gateway for this interface. The value must be a valid IPv6
                       address.
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to set IPv6 settings for. This
                       name must be an interface listed in the interface list command. (required)
 -P|--peer-dns=<bool>  A boolean value to indicate if the system should use the DNS settings
                       published via DHCPv6 for this interface.

address

• list

This command will list all of the IPv6 addresses currently assigned to the system

• esxcli network ip interface ipv6 address list

• add

Add a static IPv6 address to a given VMkernel network interface.

• esxcli network ip interface ipv6 address add CMD_OPTIONS

CMD_OPTIONS
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to add a static IPv6 address to.
                       This name must be an interface listed in the interface list command.
                       (required)
 -I|--ipv6=<str>       The IPv6 address to add to the given VMkernel network interface. This must
                       be in X:X:X::/X format (required)

• remove

Remove an IPv6 address from a given VMkernel network interface.

• esxcli network ip interface ipv6 address remove CMD_OPTIONS

CMD_OPTIONS
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to remove an IPv6 address from.
                       This name must be an interface listed in the interface list command.
                       (required)
 -I|--ipv6=<str>       The IPv6 address to remove from the given VMkernel network interface. This
                       must be in X:X:X::/X format (required)

tag

• get

Gets the tags set on the given VMkernel network interface.

• esxcli network ip interface tag get INTERFACE

• add

Adds a tag on a given VMkernel network interface. Supported tags are: Management, VMotion, faultToleranceLogging, vSphereReplication, vSphereReplicationNFC, vSphereProvisioning, VSAN, VSANWitness

• esxcli network ip interface tag add INTERFACE'TAGNAME'

• remove

Removes a tag on a given VMkernel network interface.

• esxcli network ip interface tag remove INTERFACE'TAGNAME'

INTERFACE
  -i|--interface-name=<str>
                       Name of the VMkernel network interface (vmknic) whose tags are to be
                       read/set/removed (required)
                       This name must be an interface listed in the interface list command.
                       (required)
TAGNAME
 -t|--tagname=<str>    Tag name to assign to the interface (required)

ipsec

sa

• list

List configured Security Associations

• esxcli network ip ipsec sa list

• add

Add a Security Association.

• esxcli network ip ipsec sa add CMD_OPTIONS

CMD_OPTIONS
 -e|--encryption-algorithm=<str>
                       Encryption algorithm for the Security Association. Should be one in set
                       [null, 3des-cbc, aes128-cbc]. (required)
 -k|--encryption-key=<str>
                       Encryption key(ASCII or hex). Length of hex key is dependent upon algorithm
                       used. Required when a encryption algorithm has been specified.
 -i|--integrity-algorithm=<str>
                       Integrity algorithm for the Security Association. Should be one in set
                       [hmac-sha1, hmac-sha2-256]. (required)
 -K|--integrity-key=<str>
                       Integrity key(ASCII or hex). Length of hex key is dependent upon algorithm
                       used. (required)
 -d|--sa-destination=<str>
                       Ipv6 address of Security Association destination. Can be specified as 'any'
                       or a correct IPv6 address. (required)
 -m|--sa-mode=<str>    Security Association mode. Should be one in set  [transport, tunnel].
 -n|--sa-name=<str>    Name for the Security Association to be added. (required)
 -s|--sa-source=<str>  Ipv6 address of Security Association source. Can be specified as 'any' or a
                       correct IPv6 address. (required)
 -p|--sa-spi=<str>     SPI value for the Security Association(hex). (required)

• remove

Operation to remove Security Association(s)

• esxcli network ip ipsec sa remove CMD_OPTIONS

CMD_OPTIONS
 -a|--remove-all       Set to remove all Security Associations.
 -d|--sa-destination=<str>
                       Ipv6 address of Security Association destination. This
                       option needs to be specified when removing an auto SA.
 -n|--sa-name=<str>    Name for the Security Association to be removed.
                       Specify 'auto' to remove an auto SA.
 -s|--sa-source=<str>  Ipv6 address of Security Association source. This
                       option needs to be specified when removing an auto SA.
 -p|--sa-spi=<str>     SPI value for the Security Association (hex). This
                       option needs to be specified when removing an auto SA

sp

• list

List configured Security Policys

• esxcli network ip ipsec sp list

• add

Add a Security Policy.

• esxcli network ip ipsec sp add CMD_OPTIONS

CMD_OPTIONS
 -A|--action=<str>     Action for Security Policy. Should be one in set  [none, discard, ipsec].
 -P|--destination-port=<long>
                       Destination Port for Security Policy. '0' stands for 'any' (required)
 -w|--flow-direction=<str>
                       Flow direction for Security Policy. Should be one in set  [in, out].
 -a|--sa-name=<str>    Name for the Security Association. Not being Specified lets vmkernel
                       automatically choose an Security Association. If no applicable Security
                       Association exists, then vmkernel may request one using IKE.
 -p|--source-port=<long>
                       Source Port for Security Policy. '0' stands for 'any' (required)
 -d|--sp-destination=<str>
                       Ipv6 address and prefix length of Security Policy destination. Can be
                       specified as 'any' or a correct Ipv6 network address. (required)
 -m|--sp-mode=<str>    Security Policy mode. Should be one in set  [transport, tunnel].
 -n|--sp-name=<str>    Name for the Security Policy to be added. (required)
 -s|--sp-source=<str>  Ipv6 address and prefix length of Security Policy source. Can be specified
                       as 'any' or a correct IPv6 network address. (required)
 -u|--upper-layer-protocol=<str>
                       Upper layer protocol for Security Policy, Should be one in set  [any, tcp,
                       udp, icmp6].

• remove

Operation to remove Security Policy

• esxcli network ip ipsec sp remove PARAM

PARAM
--remove-all OR --sa-name

neighbor

• list

List ARP table entries

• esxcli network ip neighbor list

• remove

Remove ARP table entries

• esxcli network ip neighbor remove CMD_OPTIONS

CMD_OPTIONS
 -i|--interface-name=<str>
                       The name of the VMkernel network interface to remove the neighbor entry
                       from. If not specified, neighbor will be removed from all interfaces
 -a|--neighbor-addr=<str>
                       The IPv4/IPv6 address of the neighbor. (required)
 -N|--netstack=<str>   The network stack instance; if unspecified, use the default netstack
                       instance
 -v|--version=<str>    IP version :  [4, 6] (required)

netstack

• list

This command will list the VMkernel Netstack instances currently known to the system.

• esxcli network ip netstack list

• get

Get runtime/configuration settings for a given Netstack Instance.

• esxcli network ip netstack get NETSTACK

• add

Add a new Netstack Instance.

• esxcli network ip netstack add NETSTACK DISABLE

• remove

Remove a new Netstack Instance.

• esxcli network ip netstack remove NETSTACK

• set

Configure settings for a given Netstack Instance.

• esxcli network ip netstack set NETSTACK CMD_OPTIONS

NETSTACK
 -N|--netstack=<str>   The network stack instance (required)
DISABLE
 -d|--disabled         Create the netstack instance only in config i.e. in disabled state. Does
                       not create in kernel.
CMD_OPTIONS
 -c|--ccalgo=<str>     The TCP Congestion Contol Algorithm for this netstack instance (not applied
                       to existing connections).:
                           cubic: Set cubic as the algorithm
                           newreno: Set newreno as the algorithm
 -e|--enable=<bool>    Enable the netstack instance (create in kernel)
 -i|--ipv6enabled=<bool>
                       To enable IPv6 for this netstack instance (aplied only during netstack
                       creation).
 -m|--maxconn=<long>   The maximum number of connections for this netstack instance (applied only
                       during netstack creation).
 -n|--name=<str>       The name for this netstack instance.

route

ipv4

• list

List configured IPv4 routes

• esxcli network ip route ipv4 list

• add

Add IPv4 route to the VMkernel.

• esxcli network ip route ipv4 add GATEWAY [NETSTACK] NETWORK

• remove

Remove IPv4 route

• esxcli network ip route ipv4 remove GATEWAY [NETSTACK] NETWORK

ipv6

• list

List configured IPv6 routes

• esxcli network ip route ipv6 list

• add

Add IPv6 route to the VMkernel.

• esxcli network ip route ipv6 add GATEWAY [NETSTACK] NETWORK

• remove

Remove IPv6 route from the VMkernel

• esxcli network ip route ipv6 remove GATEWAY [NETSTACK] NETWORK

GATEWAY
 -g|--gateway=<str>    The Ipv6 address of the gateway through which a route to be removed
                       (required)
NETSTACK
 -N|--netstack=<str>   The network stack instance; if unspecified, use the default netstack
                       instance
NETWORK
 -n|--network=<str>    The Ipv6 address and prefix length of the network to remove the route from.
                       Specify 'default' to indicate the default network. (required)

multicast

group

• list

List all the multicast group members.

• esxcli network multicast group list

nic

• list

This command will list the Physical NICs currently installed and loaded on the system.

• esxcli network nic list

• get

Get the generic configuration of a network device

• esxcli network nic get NIC_NAME

• set

Set the general options for the specified ethernet device.

• esxcli network nic set NIC_NAME CMD_OPTIONS

• down

Bring down the specified network device.

• esxcli network nic down NIC_NAME

• up

Bring up the specified network device.

• esxcli network nic up NIC_NAME

NIC_NAME
 -n|--nic-name=<str>   The name of the NIC to configured. This must be one of the cards listed in
                       the nic list command. (required)
CMD_OPTIONS
 -a|--auto             Set the speed and duplexity settings to autonegotiate.
 -D|--duplex=<str>     The duplex to set this NIC to. Acceptable values are : [full, half]
 -l|--message-level=<long>
                       Sets the driver message level. Meaning differ per driver.
 -P|--phy-address=<long>
                       Set the PHY address of the device
 -p|--port=<str>       Selects device port. Available device ports are
                           aui: Select AUI (Attachment Unit Interface) as the device port
                           bnc: Select BNC (Bayonet Neill-Concelman) as the device port
                           da: Select DA (Direct Attach copper) as the device port
                           fibre: Select fibre as the device port
                           mii: Select MII (Media Independent Interface) as the device port
                           tp: Select TP (Twisted Pair) as the device port
 -S|--speed=<long>     The speed to set this NIC to, in Mbps. Acceptable values are : [10, 100,
                       1000, 2500, 5000, 10000, 20000, 25000, 40000, 50000, 56000, 100000]
 -t|--transceiver-type=<str>
                       Selects transeiver type. Currently only internal and external can be
                       specified, in the future future types might be added. Available transeiver
                       types are
                           external: Set the transceiver type to external
                           internal: Set the transceiver type to internal
 -V|--virtual-address=<str>
                       Set the virtual address of the device
 -w|--wake-on-lan=<str>
                       Sets Wake-on-LAN options. Not all devices support this. The argument to
                       this option is a string of characters specifying which options to enable.
                       p Wake on phy activity
                       u Wake on unicast messages
                       m Wake on multicast messages
                       b Wake on broadcast messages
                       a Wake on ARP
                       g Wake on MagicPacket(tm)
                       s Enable SecureOn(tm) password for MagicPacket(tm)

coalesce

• get

Get coalesce parameters

• esxcli network nic coalesce get

• set

Set coalesce parameters on a nic

• esxcli network nic coalesce set NIC_NAME [CMD_OPTIONS]

NIC_NAME
 -n|--vmnic=<str>      Name of vmnic to set coalesce parameters. (required)
CMD_OPTIONS
 -a|--adaptive-rx=<bool>
                       enable or disable adaptive RX algorithm in driver.
 -A|--adaptive-tx=<bool>
                       enable or disable adaptive TX algorithm in driver.
 -R|--rx-max-frames=<long>
                       Maximum number of RX frames driver to process before interrupting.
 -r|--rx-usecs=<long>  Number of microseconds driver to wait for RX before interrupting.
 -i|--sample-interval=<long>
                       Packet rate sampling internal in seconds for the adaptive coalescing
                       algorithm in driver.
 -T|--tx-max-frames=<long>
                       Maximum number of completed TX frames driver to process before
                       interrupting.
 -t|--tx-usecs=<long>  Number of microseconds driver to wait for completed TX before interrupting.

high

• get

Get information about the behavior of a NIC when it sends or receives packets at high packet rate.

• esxcli network nic coalesce high get NIC_NAME

• set

Set parameters to control the behavior of a NIC when it sends or receives packets at high packet rate.

• esxcli network nic coalesce high set NIC_NAME [CMD_OPTIONS]

low

• get

Get information about the behavior of a NIC when it sends or receives packets at low packet rate.

• esxcli network nic coalesce low get NIC_NAME

• set

Set parameters to control the behavior of a NIC when it sends or receives packets at low packet rate.

• esxcli network nic coalesce low set NIC_NAME [CMD_OPTIONS]

NIC_NAME
 -n|--vmnic=<str>      The name of the pnic for which information should be retrieved. (required)
CMD_OPTIONS
 -p|--pkt-rate=<long>  The high packet rate measured in number of packets per second. When packet
                       rate is above this parameter, the RX/TX coalescing parameters configured by
                       this command are used.
 -R|--rx-max-frames=<long>
                       The maximum number of RX packets to delay an RX interrupt after they arrive
                       under high packet rate conditions.
 -r|--rx-usecs=<long>  The number of microseconds to delay an RX interrupt after a packet arrives
                       under high packet rate conditions.
 -T|--tx-max-frames=<long>
                       The maximum number of TX packets to delay an TX interrupt after they are
                       sent under high packet rate conditions.
 -t|--tx-usecs=<long>  The number of microseconds to delay a TX interrupt after a packet is sent
                       under high packet rate conditions.
 -n|--vmnic=<str>      Name of the vmnic for which parameters should be set. (required)

cso

• get

Get checksum offload settings

• esxcli network nic cso get

• set

Set checksum offload settings on a nic

• esxcli network nic cso set CMD_OPTIONS

CMD_OPTIONS
 -e|--enable=<long>    RX/TX checksum offload (required)
 -n|--vmnic=<str>      Name of vmnic to set offload settings. (required)

eeprom

• dump

Dump device EEPROM

• esxcli network nic eeprom dump CMD_OPTIONS

CMD_OPTIONS
 -l|--length=<long>    Bytes of EEPROM to dump
 -o|--offset=<long>    Offset of EEPROM starting to dump
 -n|--vmnic=<str>      The name of pnic to dump EEPROM (required)

• change

Change EEPROM on a nic

• esxcli network nic eeprom change CMD_OPTIONS

CMD_OPTIONS
 -f|--file=<str>       File name of new EEPROM content
 -m|--magic=<long>     Magic key of EEPROM (required)
 -o|--offset=<long>    Offset of EEPROM to change
 -v|--value=<long>     New EEPROM value in double word
 -n|--vmnic=<str>      Name of vmnic to change EEPROM. (required)